Need help? 251-680-7500 Mon–Fri · 7 AM – 4 PM
Electrical Troubleshooting · Mobile, AL

Outlet Not Working: Why an Electrical Outlet Goes Dead and How to Fix It

A dead outlet is the most common electrical problem there is, and half the time the fix is pressing a button in the garage. The other half are loose connections, failed devices and burned wiring that should be handled by a licensed electrician. Here is how to tell which half yours is in, in a Mobile home, before you call.

Call (251) 680-7500   Request a Quote
Why Outlets Die

Six Reasons an Outlet Stops Working

An outlet goes dead because the power stopped arriving, or because the device itself failed. These are the causes in the order we find them in Mobile homes, and the first three cost nothing to check:

  • A tripped GFCI somewhere else Kitchen, bathroom, garage and outdoor outlets are often protected by one GFCI that feeds the rest. When it trips, outlets in other rooms go dead with it.
  • A tripped breaker Sometimes a tripped breaker sits in the middle position and looks on. Push it fully off, then on.
  • A switched outlet Many living rooms and bedrooms have an outlet controlled by a wall switch for a lamp. The switch is off.
  • A loose or backstabbed connection Wires pushed into the holes on the back of a receptacle loosen over time. The outlet, and everything downstream of it, goes dead, and the loose connection runs hot.
  • A failed or burned receptacle Outlets wear out. A plug that falls out, a cover plate that is warm, or scorch marks mean the device has failed, and the cause may be upstream.
  • A broken wire or a failed splice In the box, in the attic or behind a wall. Found with a tracer, not by guessing.

The first reason on that list is the one we are happiest to find. Two outlets had stopped working in a Theodore home. By the time our electrician got there, both were working again; most likely a GFCI somewhere else had tripped and been reset. He tested both outlets, explained what had probably happened and did not sell a repair that was not needed.

Call (251) 680-7500
Professional Systems electrician installing a GFCI outlet in a Gulf Coast kitchen
Check These First

What to Check Before You Call

Plug a lamp you know works into the dead outlet, then into the other half of it; outlets can be half-dead. Find every GFCI in the house, including the garage, the bathrooms, the kitchen, the laundry and outside under the weatherproof covers, and press TEST then RESET on each. Check the breaker panel for a breaker in the middle position and cycle it fully off and on once. Flip the wall switches in the room; one of them may control the outlet.

If the outlet is warm, discolored, buzzing or smells, stop: turn off the breaker for that circuit and call. Do not pull the outlet out of the wall to look. A burned receptacle is often the visible end of a loose connection or an aluminum wire upstream, and that is exactly the repair that should be made by someone licensed, with the power off and the right connectors.

If a whole room is dead and the breaker will not reset, skip the rest of the checks. A Fairhope homeowner had a room with no power and a breaker that would not flip back on, and she was worried about a fire. She asked for someone that day, and an electrician was there that same day to track it down.

During the Visit

What the Electrician Does

✓

Trace the circuit

Where the power stops, and why: the GFCI, the breaker, the upstream device or a splice in the attic. Found with a tracer and a meter.

✓

Remake the connections

Backstabbed and loose connections are remade on the screw terminals; aluminum wiring gets the correct connectors. The outlet that was dead and the ones that were about to be.

✓

Replace failed devices

Worn, burned or loose receptacles replaced with tamper-resistant devices, and GFCI protection added where current code calls for it.

✓

Check for heat damage

The box, the wires and the devices upstream are inspected for the browning and brittleness that a hot connection leaves behind.

✓

Add the circuit the house needed

If the outlet died because a space heater, a window unit or a freezer was asking too much of it, a dedicated circuit is the real fix, and we quote it on the visit.

✓

Price in writing

The cause and the price are written down before any repair. Most dead outlets are fixed the same visit.

Outlet dead and the GFCI didn't fix it?

Licensed electricians across Mobile and Baldwin counties, same-day on most weekdays, the price in writing before the work.

Professional Systems electrician installing a GFCI outlet in a Gulf Coast kitchen
Older Homes

Dead Outlets in Mobile's Older Houses: Backstabs, Aluminum and Ungrounded Circuits

Houses built from the mid-1960s through the 1980s, which is a large share of Mobile, Prichard, Saraland and Theodore, were wired with receptacles that let the electrician push the wire into a hole on the back instead of wrapping it around a screw. Those push-in connections loosen as copper expands and contracts through forty summers, and when they loosen they arc, heat and eventually open. The outlet goes dead, and so does every outlet fed through it. The same era brought aluminum branch wiring to some neighborhoods, which loosens and oxidizes at every connection unless the right connectors are used.

Older still, the pre-1960s houses in Midtown and the Oakleigh district often have two-prong ungrounded outlets, and sometimes a three-prong outlet someone installed on a two-wire circuit. We fix dead outlets in all of these properly, and when a house shows the pattern on several circuits we say so and talk about what a rewire or a partial rewire would involve.

In houses with aluminum wiring, a dead or crackling outlet is often a problem with the connection behind it. A Mobile homeowner heard crackling behind the washer and dryer on a Sunday and called us. A person answered, and an electrician was there the next morning. The dryer receptacle was a 15-amp device on a 20-amp circuit with loose connections, in a house with aluminum wiring; he replaced it and made the connections the way aluminum wire requires. Her review afterward: “I called Professional Systems on a Sunday, spoke to a live human, and they came out the next morning, right on time.”

Reviews

What Homeowners Say

★★★★★

"I heard crackling noises behind my washer/dryer. I called Professional Systems on a Sunday, spoke to a live human, and they came out the next morning, right on time. They found the dryer receptacle was a 15 amp receptacle on a 20 amp circuit with loose connections, changed it and made the proper connections as I have aluminum wiring."

— Jo S., Google review
★★★★★

"Professional Systems did an excellent job with our electrical work. Professional, on time, and the quality speaks for itself."

— Lilli A., Google review
★★★★★

"Excellent service and professionalism. Arrived on time, cleaned up after and did a great follow up. Will definitely use this company again!"

— Deanna N., Google review

Read More Reviews

Questions & Answers

Outlet Not Working: Questions We Hear

Why is my outlet dead but the breaker is not tripped?

Most often a tripped GFCI somewhere else in the house protecting that outlet, a wall switch that controls it, or a loose connection at an upstream outlet that has opened the circuit. Check the GFCIs and the switches first; the loose connection needs an electrician.

Where are the GFCIs that could control this outlet?

Garage, bathrooms, kitchen, laundry, basement and outdoors, under the weatherproof covers. One GFCI often protects outlets in several rooms. Press TEST and RESET on every one.

Only half of the outlet works. What is that?

A receptacle wired so one half is switched, or a failed device, or a broken tab. A quick fix during the visit.

The outlet is warm and the plug falls out. Is that dangerous?

Yes. A warm outlet is a loose connection making heat, and a loose plug is a worn receptacle doing the same. Turn the breaker off for that circuit and have it replaced; it is one of the cheapest fire-prevention repairs there is.

Can I replace an outlet myself?

Many homeowners do, and many of the burned outlets we replace were installed that way. If the house has aluminum wiring, two-prong outlets, or any sign of heat, have a licensed electrician do it with the power verified off and the right connectors.

How much does it cost to fix a dead outlet?

A GFCI reset is free advice on the phone. A failed receptacle, a loose connection or a switched-outlet mystery is a small same-visit repair. A broken wire in a wall or a circuit that needs rewiring is more, and the electrician writes the price down before any work. On a weekday, a technician's visit is a flat $175 diagnostic fee that covers the first hour at your home or business; parts and anything beyond that are priced in writing before we do them.

Something we didn't cover? See our full FAQ page or call (251) 680-7500.

Explore More

Get It Fixed

Outlets, Switches & Exterior Receptacles

Replacement, GFCI protection and new receptacles where the house needs them.

Outlets & Switches

Whole-House Rewiring

Knob-and-tube, aluminum and the houses where dead outlets are a pattern.

Rewiring

Contact Us

Send the form or call; a person answers during business hours.

Contact
Get Started Today

Dead Outlet? Call Now.

Licensed electricians, same-day on most weekdays, the cause found and the price in writing before the work.

Call (251) 680-7500   Request a Quote